|
Kto jest w sklepie?
Sklep przegląda 5443 gości i 1 zarejestrowany klient
|
Kategorie
|
Informacje
|
Polecamy
|
|
|
|
|
Dla tego produktu nie napisano jeszcze recenzji!
;
Dobrej jakości skan - wkońcu mogłem poznać wszystkie funkcje tego odtwarzacza - polecam .
;
Gruba instrukcja - poprostu wszystko co potrzreba - polecam .
CONFIGURING THE REMOTE
most likely want to use the AVR 7200�s volume control commands even when the remote has been set to issue all other commands for the video device. �Punchthrough� enables you to easily program the remote to do this. Volume Punch-Through Follow these steps to enable the Volume Up/Down and Mute controls from one device to be used when the remote is otherwise programmed for a different device. NOTE FOR VOLUME PUNCH-THROUGH: The remote�s default settings are for the AVR 7200�s volume controls, to be used when any input or device is selected, with the exception of the VID 2/TV button. There is no need to program the remote for volume punch-through for the AVR 7200�s controls with other sources, such as DVD. To have the AVR 7200�s volume commands used when the TV device is selected, follow these steps: 1. Press and hold the Program Button O for about three seconds while the message shown in Figure 15 appears in the remote�s LCD Information Display 2. Release the button when the red light under the Set Button F appears. 2. The remote�s MAIN MENU message (Figure 16), will appear in the LCD display and the Set Button F will remain illuminated in red. Press the � / ¤ Navigation Button n until PUNCHTHROUGH appears on the bottom line of the LCD screen, as shown in Figure 48. Press the Set Button F to enter the main punch-through menu branch.
MAIN MENU PUNCH-THROUGH
5. At the next display screen (Figure 51), you will select the device whose Volume Up/Down and Mute commands will be used. Press the � / ¤ Navigation Button n until the desired device�s name appears to the right of the device in use. In our example, that is the AVR 7200 (indicated by AVR). When the desired combination of devices appears, press the Set Button F.
PUNCH-THROUGH TV<-AVR
Cable device will be transmitted when the VID 1/VCR device has been selected as the current device. 1. Press and hold the Program Button O for about three seconds while the message shown in Figure 15 appears in the remote�s LCD Information Display 2. Release the button when the red light under the Set Button F appears. 2. The remote�s MAIN MENU message (Figure 16), will appear in the LCD display and the Set Button F will remain illuminated in red. Press the � / ¤ Navigation Button n until PUNCHTHROUGH appears on the bottom line of the LCD screen, as shown in Figure 48. Press the Set Button F to enter the main punch-through menu branch. 3. At the next menu screen, press the � / ¤ Navigation Button n until CHANNEL appears on the bottom line of the LCD screen, as shown in Figure 54. Press the Set Button F to begin programming the remote for Channel punch-through.
PUNCH-THROUGH CHANNEL
Figure 51
6. When the Set button is pressed, the display will change to show you that the new combination of control commands is being saved to the unit�s memory, as shown in Figure 52. The word SAVED will flash four times and then the remote will return to normal operation.
TV<-AVR [VOL] SAVED
Figure 52
7. Once the punch-through is programmed, the Volume Up/Down and Mute buttons of the second device named will be used when those buttons HV are pressed while the master device is in use. Returning the Volume Control Settings to Default Operation: If you wish to remove the Volume punch-through so that the commands for Volume and Mute are returned to the factory default setting, follow the steps shown above, except that in Steps 4 and 5, select the same device for both the DEVICE IN USE on the left side of the bottom line and the PUNCH-THROUGH device. In the example used, the display to return the remote to default settings will appear as shown in Figure 53.
PUNCH-THROUGH TV<-TV
Figure 54
4. The next display screen (Figure 55) is where you select the device that will receive the punchthrough commands. In our example, that is the VID 2/ TV button, as that is where we want the cable box�s channel controls to be active. Press the � / ¤ Navigation Button n until the name of the base device appears and then press the Set Button F.
DEVICE IN USE VCR
Figure 48
3. At the next menu screen (Figure 49) press the Set Button F to begin programming the remote for Volume punch-through.
PUNCH-THROUGH VOLUME
Figure 55
5. At the next display screen (Figure 56), you will select the device whose Channel Up/Down commands will be used. Press the � / ¤ Navigation Button n until the desired device name appears to the right of the device in use. In our example, that is the cable box. When the desired combination of devices appears, press the Set Button F.
PUNCH-THROUGH VCR<-CBL
Figure 53
Channel Punch-Through Channel punch-through allows the Channel Up/Down buttons to send commands to a different device than the one that has been selected for other commands. For example, you may wish to use a cable box or satellite receiver as the source for a VCR, so you would want the Channel Up/Down Selectors X to transmit commands to the cable box even though the other button commands are programmed to operate the VCR. To program the remote for Channel punch-through, follow these steps. This example will show how to program channel punch-through so that the commands programmed for Channel Up/Down for the VID 3/
Figure 49
4. The next display screen (Figure 50) is where you select the device that will receive the punchthrough commands. In our example, that is the VID 2/TV button, as that is where we want the AVR 7200�s volume controls to be active. Press the � / ¤ Navigation Button n until the name of the base device appears and then press the Set Button F.
DEVICE IN USE TV
Figure 56
Figure 50
6. When the Set button is pressed, the display will change to show you that the new combination of control commands is being saved to the unit�s memory, as shown in Figure 57. The word SAVED will flash four times and then the remote will return to normal operation.
CONFIGURING THE REMOTE
43
|
|
|
> |
|